• 'Power Link' Adapter

    for LightRider Motorcycle Helmet Light

    The 'Power Link' adapter enables your LightRider motorcycle helmet light to receive power directly from your motorcycle battery. You never have to recharge - lighting is constant as long as you're connected. The adapter automatically unlinks when you get off your bike. Connect your adapter to your helmet light using either the Standard Power Cord or Strobing Power Cord. Includes:
    • ‘Power Link’ motorcycle battery cable (3A blade fuse)
    • Disconnect adapter with belt clip
    • Tank clip to store battery cable connector
    Compatible with LightRider ('Power Link') only. Download user guide
  • Ballistic Nylon Battery Holster

    for the 'Power Protected' 3000mAh Battery

    This rugged holster of woven ballistic nylon holds the Lumenflex 3000mAh 'Power Protected' battery. Used for all products in which this battery pack is worn at the waist.   Compatible with LightRider (Rechargeable), OrbitSun, OrbitSunXT, and BrimBeam Boost.
  • 'Power Protected' Battery Pack for BrightCycle

    BrightCycle Bicycle Helmet Light Replacement Battery

    • Uses genuine 12V TrustFire li-ion batteries rated at 900 mAh (CE, FCC, & PSE certifications)
    • 'Power Protected' means that battery cell protection circuitry prevents over-charging and over-discharging
    • Cabling uses 22 AWG wire for long term reliability
    • Charges in approx 45 minutes with 1 Amp "smart" charger
    • Cable connector: DC jack (2.1mm ID x 5.5mm OD)
    • Operating times: 3 hours steady state, 6 hours flashing
      Compatible with BrightCycle only. International Customers:  Export regulations prevent Lumenflex from shipping battery packs ordered separately from equipment.
  • 'Power Protected' Battery Pack for BrimBeam

    BrimBeam Baseball Cap Light Replacement Battery

    • Uses genuine 12V TrustFire li-ion batteries rated at 900 mAh (CE, FCC, & PSE certifications)
    • 'Power Protected' means that battery cell protection circuitry prevents over-charging and over-discharging
    • Cabling uses 22 AWG wire for long term reliability
    • Charges in approx 45 minutes with 1 Amp "smart" charger
    • Cable connector: DC jack (2.1mm ID x 5.5mm OD)
    • Operating time: 3.5 hours
      Compatible with BrimBeam only. International Customers:  Export regulations prevent Lumenflex from shipping battery packs ordered separately from equipment.
  • "Power Protected" Battery Pack (12V, 3,000 mAh)

    • Uses genuine 12V TrustFire li-ion batteries rated at 3,000 mAh (CE, FCC, & PSE certifications)
    • 'Power Protected' means that battery cell protection circuitry prevents over-charging and over-discharging
    • Cabling uses 22 AWG wire for long term reliability
    • Speed charger (with charge protection circuitry) charges in approximately 6 hours
    • Cable connector: DC jack (2.1mm ID x 5.5mm OD)
    For battery run times, see individual products. Compatible with LightRider (Rechargeable) and SiteLight.
  • Li-ion "Smart" Charger (2 Amps / 24 Watts)

    Replacement Charger

    • "Smart" charging circuitry stops charging when charge is complete.
    • Protects from common li-ion failures due to over-charging.
    • LED changes from green to red while charging.
    • Charges twice as fast as our standard 1 Amp "smart" charger
    • Cable connector: DC jack (2.1mm ID x 5.5mm OD)
    Compatible with all Lumenflex batteries.
  • Power Cord

    with ON/OFF switch

    This cord is for lights that use our 3,000 mAh 'Power Protected' battery pack. It has a DC male connector (2.1mm ID x 5.5mm OD) on each end. The connector that attaches to the helmet has a waterproof housing. The coiled power cord includes an ON/OFF switch. Compatible with LightRider (Rechargeable) and SiteLight.
  • Power Cord

    No Switch

    Cord has two male connectors (2.1mm ID x 5.5mm OD), one straight and one right angle. The straight connector attaches to the helmet and has a waterproof housing. The right angle connector attaches to the 'Power Link' adapter. Compatible with LightRider 'Power Link' only.
  • Power Cord

    with Strobe Controller

    Use this power cord to add strobing capabilities to your Lumenflex lights. The digital controller has seven 7 flashing modes and 5 brightness levels. Each end has a DC male connector (2.1mm ID x 5.5mm OD). The connector that attaches to the helmet has a waterproof housing. Compatible with LightRider (Rechargeable or 'Power Link'). NOTE: Some states restrict flashing lights on public roads. Before buying the strobe controller, check your state’s transportation code to make sure flashing lights are allowed.
  • Reinstallation Kit

    for the LightRider Helmet LED Light

    Kit Includes:
    • Pressure-sensitive 3M tape specified for Lumenflex LED bands
    • Removable guide tape to layout the LED pattern
    • Velcro fastener to store helmet cable connector
    • Helmet cleaning pads
    Compatible with LightRider (Rechargeable and 'Power Link') only.

Title

Go to Top